高熵形状记忆合金的研究进展

高熵形状记忆合金是在等原子比NiTi合金的基础上,结合高熵合金的概念,逐渐发展起来的一种新型高温形状记忆合金。近年来,已开发出了综合性能优异的(TiZrHf)50(NiCoCu)50系和(TiZrHf)50(NiCuPd)50系高熵形状记忆合金,引起了广泛的关注和研究兴趣。本文从物相组成、微观组织、马氏体相变行为、形状记忆效应和超弹性等角度出发,综述了高熵形状记忆合金的研究进展,并对高熵形状记忆合金未来的研究重点进行了展望。     

Investigation the effect of FeNiCoCrMo HEA addition on properties of B4C ceramic prepared by spark plasma sintering

In this study, monolithic B₄C and B₄C-based ceramics incorporating FeNiCoCrMo dual-phase (FCC and BCC) high entropy alloys (HEAs) were produced by spark plasma sintering (SPS). The effect of additives on the densification behavior, mechanical properties, microstructures, and phase evaluation of the samples were investigated. X-ray analysis confirmed the existence of FCC structured HEA and depletion of BCC structured HEA, after high-temperature reaction between B₄C-HEAs. The addition of HEAs enhanced the densification behavior by liquid phase sintering. Furthermore, hardness and fracture toughness values of the samples increased with increasing HEAs content. Fracture toughness and hardness values for all composites were higher than the monolithic B₄C. A combination of the highest density (∼99.22 %) and the best mechanical properties (32.3 GPa hardness and 4.53 MPa m^1/2 fracture toughness) was achieved with 2.00 vol.% HEA addition.     

VO2/GaAs异质结的制备及其光电特性研究

采用直流磁控溅射和后退火氧化工艺在p型GaAs单晶衬底上成功制备了n-VO_2/pGaAs异质结,研究了不同退火温度和退火时间对VO_2/GaAs异质结性能的影响,并分析其结晶取向、化学组分、膜层质量以及光电特性。结果表明,在退火时间2 h和退火温度693 K下能得到相变性能最佳的VO_2薄膜,相变前后电阻变化约2个数量级。VO_2/GaAs异质结在308 K、318 K和328 K温度下具有较好的整流特性,对应温度下的阈值跳变电压分别为6.9 V、6.6 V和6.2 V,该结果为基于VO_2相变特性的异质结光电器件的设计与应用提供了可行性。     

Intrinsic Defect Limit to the Growth of Orthorhombic HfO2 and (Hf,Zr)O2 with Strong Ferroelectricity: First-Principles Insights

It is believed that promoting the fraction of ferroelectric orthorhombic phase (o-phase) through O-poor growth conditions can increase the spontaneous polarization of HfO₂ and (Hf,Zr)O₂ thin films. However, the first-principles calculations show that the growth may be limited by the easy formation of point defects in the orthorhombic and tetragonal phases of HfO₂, ZrO₂, and (Hf,Zr)O₂. Their dominant defects, O interstitial (O_i) under O-rich conditions and O vacancy (V_O) under O-poor condition, have low formation energies and quite high density (10¹⁶–10¹⁹ cm⁻³ for 800–1400 K growth temperature). Especially, O_i has negative formation energy in tetragonal HfO₂ under O-rich condition, causing non-stoichiometry and limiting the crystalline-seed formation during o-phase growth. High-density defects can cause disordering of dipole moments and increase leakage current, both diminishing the polarization. These results explain the experimental puzzle that the measured polarization is much lower than the ideal value even in O-poor thin films and highlight that controlling defects is as important as promoting the o-phase fraction for enhancing ferroelectricity. The O-intermediate condition (average of O-rich and O-poor conditions) and low growth temperature are proposed for fabricating HfO₂ and (Hf,Zr)O₂ with fewer defects, lower leakage current, and stronger ferroelectricity, which challenges the belief that O-poor condition is optimal.     

Mechanical properties and wear behavior of Tin+1(Al,A)Cn (A = Ga,In, Sn,n = 1, 2) via quasi-high-entropy of single atomic thick A layer

The strengthening method of multi-element M-site solid solution is a common approach to improve mechanical properties of MAX phase ceramic. However, the research on capability of multi-element A-site solid solution to improve mechanical properties has rarely been reported. Thereupon, quasi-high-entropy MAX phase ceramic bulks of Ti₂(Al_1?xA_x)C and Ti₃(Al_1?xA_x)C₂ (A = Ga, In, Sn, x = 0.2, 0.3, 0.4) were successfully synthesized by in situ vacuum hot pressing via multi-elements solid solution. The multi-elements solid solution in single-atom thick A layer was confirmed by X-ray diffraction and X-ray photoelectron spectroscopy as well as by energy dispersive X-ray spectroscopy mappings. Effects of doped multi-elements contents on the phase, microstructure, mechanical properties, and high temperature tribological behaviors were studied. Results demonstrated that the Vickers hardness, anisotropic flexural strength, fracture toughness, and tribological properties of Ti–Al–C based MAX ceramics could be remarkably improved by constitution of quasi-high-entropy MAX phase in A layers. Moreover, the strengthening and wear mechanisms were also discussed in detail. This method of multi-element solid solution at A-site provides new way to enhance mechanical properties of other MAX phase ceramics.     

Liquid-phase epoxidation of propylene with molecular oxygen by chloride manganese meso-tetraphenylporphyrins

Propylene molecule owns two active sites, the direct epoxidation of propylene by dioxygen is still a challenge due to the limitation of selectivity. In this work, the direct liquid-phase propylene aerobic epoxidation protocol by chloride manganese meso-tetraphenylporphyrin (MnTPPCl) was developed. The conversion of propylene was 12.7%, and the selectivity towards PO (propylene oxide) reached up to 80.5%. The formation of PO was attributed to the mechanism via high-valent Mn species, which was confirmed by means of in situ UV–vis spectrum.     

Effect of impact angle on wear behavior of Mo2NiB2–Ni cermets with different Ni content

Herein, the influence of the impact angle and Ni content on the wear behavior of Mo₂NiB₂–Ni cermets was studied using an erodent-carrying slurry comprising artificial seawater and SiO₂ sands. The results reveal that the material loss may be attributed to the wear damage caused by SiO₂ sands because cermets are expected to exhibit good corrosion resistance in artificial seawater. The relative density of cermets markedly influences their resistance to wear damage, and the material loss experienced by cermets with poor relative density is 2–4 times higher than that of cermets with good relative density; this occurs because a higher relative density can markedly enhance the mechanical properties and reduce the defects in the cermets. Moreover, the results indicate that as the impact angle increases from 0° to 60°, the manifestation of the wear mechanism changes from damaging the Ni binder phase (caused by single cutting wear) to damaging both the Mo₂NiB₂ ceramic and Ni binder phases due to the combination of cutting wear and impact wear. The wear damage is dominated by the cutting wear and impact wear from SiO₂ sand at the low and high impact angles, respectively. Furthermore, the severe deterioration of the single ceramic skeleton at high impact angles indicates that the synergistic influence of the Mo₂NiB₂ ceramic and Ni binder phases on enhancing the wear resistance of the cermets intensifies at high impact angles.     

Improvement of a commercial calcium phosphate bone cement by means of drug delivery and increased injectability

Calcium phosphate cements (CPCs) have been increasingly used as synthetic bone substitutes for repair and regeneration of bone defects given their biocompatibility, resemblance to bone and malleability. Moreover, their use as local antibiotic delivery systems is of main interest against bone infections, avoiding the adverse effects of high dosages of conventional therapy. The main goals of this work were to improve the properties of a commercial CPC (Neocement®), turning it injectable, and to provide it with a new functionality as a drug delivery system able to ensure a sustained release of an antibiotic commonly used in orthopaedics (gentamicin sulphate, GS). For this, the influence of the liquid phase amount (%LP) and type of polymer contained in the formulation (chitosan, Chi, or hydroxypropyl methylcellulose, HPMC) on the basic properties of the material was evaluated. It was found that the formulation containing 42%LP + HPMC+1.87% wt GS was the best one. It showed suitable setting and mechanical properties, and injectability around 87% (much superior to the original Neocement®, with 31%). It ensured a sustained release of GS for at least 14 days, at antibacterial levels. The antibiotic released is highly effective against S. epidermidis, but also presents some antibacterial activity against S. aureus. The CPC revealed to be non-cytotoxic. Moreover, it demonstrated good flowability and connectivity with human cadaveric trabecular bone.     

Meticulously tailoring phase boundary in KNN-based ceramics to enhance piezoelectricity and temperature stability

Although KNN-based ceramics with high electrical properties are obtained through a variety of strategies, the temperature sensitivity is still one of the key technical bottlenecks hindering practical applications. Here, we use a new strategy, meticulously tailoring phase boundary, to refine the ferroelectric boundary of KNN-based ceramics, leading to high piezoelectricity companied with improving temperature stability. The highest d₃₃ value in this system reaches 501 pC/N with a T_C ∼ 240°C, whereas a large strain of ∼0.134% can be kept with 10% lower deterioration until 100°C. The origin of high piezoelectricity is mainly attributed to the well-preserved multiphase coexistence and the appearance of nanodomains, which greatly facilitate the polarization rotation. Instead of the changed intrinsic thermal insensitivity, the precision phase boundary engineering plays an important role in strengthening the temperature stability of electric-induced strain. This work provides a simple and effective method to obtain both high electrical properties and excellent thermal stability in KNN-based ceramics, which is expected to promote the practical applications in the future.     

Effect of temperature on the structure and mechanical properties of SiC–TiB2 composite ceramics by solid-phase spark plasma sintering

SiC composite ceramics have good mechanical properties. In this study, the effect of temperature on the microstructure and mechanical properties of SiC–TiB₂ composite ceramics by solid-phase spark plasma sintering (SPS) was investigated. SiC–TiB₂ composite ceramics were prepared by SPS method with graphite powder as sintering additive and kept at 1700 °C, 1750 °C, 1800 °C and 50 MPa for 10min.The experimental results show that the proper TiB₂ addition can obviously increase the mechanical properties of SiC–TiB₂ composite ceramics. Higher sintering temperature results in the aggregation and growth of second-phase TiB₂ grains, which decreases the mechanical properties of SiC–TiB₂ composite ceramics. Good mechanical properties were obtained at 1750 °C, with a density of 97.3%, Vickers hardness of 26.68 GPa, bending strength of 380 MPa and fracture toughness of 5.16 MPa m^1/2.